Woody Wax Brushes, Gloves, And Applicator Kits

FOR FIBERGLASS & NON SKID DECKS

A little "Woody" goes a long way! One ounce will treat a 25' boat with 2 months protection. This concentrated wax will protect your decks and fiberglass from the deteriorating effects of the sun, oxidation, water spots, and pollution without the use of harsh chemicals or abrasive cleaners.

You will find washing becomes more like rinsing. Nothing sticks to your deck. With an easy swipe of a brush, even dried fish blood will come off with just water. Your boat will no longer have to go through the maintenance rollercoaster of detailing and deteriorating.

 

• 
  Woody Wax Fiberglass and Non-Skid Deck Wax is fast & easy. No rubbing or buffing. Makes clean up a breeze.
• 
  Feet won't slip, salt and dirt won't stick.
• 
  Protects in all weather conditions. Keeps everything from sticking, even fish blood rinses right off.

 

HOW TO USE WOODY WAX FOR YOUR FIBERGLASS & NON SKID DECKS:

• Wash the boat and leave the deck WET.
• Always spray WOODY WAX on to a soft deck brush rather than directly on to the deck. Spray 1-2 pumps into the brush and spread from front to back of boat. USE CAUTION - THE DECKS WILL BE SLICK UNTIL THEY ARE RINSED. As you move through the boat you should brush the entire inside of the boat including the deck, smooth fiberglass, metals, electronics, connections and controls, etc.
• RINSE, starting at the bow, moving to the stern. Allow most of the water to run off or evaporate.
• Dry using a cotton towel (you are actually buffing a light film of hard wax as you dry with the towels.
• NOW YOU CAN RELAX!

HOW TO USE WOODY WAX FOR PLASTIC AND VINYL:

Bring back the color and shine to dull vinyl and plastic with a little WOODY WAX! WOODY WAX will renew the look, life and luster of sun dried plastic and vinyl and will also protect it from drying further.

For Metal Restoration & Protection

Treat metals with Woody Wax to break down corrosion and remove hard water spots and oxidation. Brightens dull metal. Simply wipe it on the metal and let it work - no buffing required. Woody Wax will protect your metals without leaving a sticky or slippery feel. Lasts up to 2 months. For 6 month protection, seal with Woody Wax Metal Sealant.

HOW TO USE WOODY WAX FOR METAL RESTORATION & PROTECTION:

ANODIZED ALUMINUM, ALUMINUM, STAINLESS & CHROME:
WOODY WAX is a "wipe on, wipe off" product that disintegrates oxidation, corrosion and water spots. Simply spray WOODY WAX on a clean cotton glove or cloth and apply to metal. For metal that is in good condition, allow WOODY WAX to remain on for approximately 30 minutes, then simply wipe with a clean cloth or disposable blue shop towel. You will be amazed by the depth and the shine that has returned to your bright work, leaving a layer of corrosion blocking wax that is not oily or sticky and lasts for about 2 months.

ANODIZED ALUMINUM AND METALS WITH ROUGH BLISTERS AND PITS:
For metals that have heavy pitting or corrosion, it may be necessary to leave WOODY WAX on overnight (it will not hurt the metals to leave on for long periods of time- it will only attack the corrosion and oxidation the longer it sits). Use a piece of fine bronze wool sprayed with WOODY WAX to rub corrosion spots. Corrosion will come right off the pitted area without hurting the metals. Two or Three applications may be necessary over a month or so to fully restore pitted metals.

OUTRIGGERS, T TOPS, TOWERS, RAILINGS, ETC.
Use WOODY WAX to treat and protect outriggers. It is best to leave WOODY WAX on the riggers for a week before wiping it off and applying the Metal Sealant. The longer WOODY WAX has to penetrate the better the metal will look when sealed.

ENGINES, ELECTRONICS AND CONNECTIONS:
With a fine mist of WOODY WAX your switches, battery terminals, antennas, fuse panels, light sockets, outboard engines, and electric motors will be corrosion-free and will look and work like the day they were new!